Website map|Add to favouritesWelcome to Ahead Technology(Shen Zhen) Co.,LTD

AHEAD product
Current location: HomeAheadMold News » Ahead News
TOOLING: Designing Molds for Easy Cleaning & Maintenance in the Press[ 01-21 14:26 ]
Pay attention to water leaks and rust, proper grease selection, vent buildup, and checks for wear. ...... Proper O-ring maintenance is important to prevent rust. O-rings degrade over time, so they should be replaced each time the tool undergoes preventive maintenance. In this column, I will discuss best ......
Ahead Mold Celebrated the Spring Festival[ 01-20 08:00 ]
In January 19, 2016, Ahead Technology (Shenzhen) Co., Ltd held annually celebration for Spring Festival, i.e., the Chinese New Year! Leaders and staff had unite wholeheartedly and created success last year. In addition to a big feast, there were also some wonderful performances: Popping performed by the Tooling Department Poetry Reading performed by the Injection Department ......
What Are "Thin Or Thick" of Injection Molded Parts?[ 01-18 10:37 ]
Not just the specifics of thermodynamics, but also a more fundamental one of Mankind (sorry, Personkind!) collectively learning from experience and recording that experience. Often, that condensed experience will end up in... that right, TEXTBOOKS. Should we all spend our time reinventing the wheel? I do despair when I read ......
The Reasons of Warpage in Injection Molding[ 01-15 16:09 ]
Warpage is usually caused by molded-in stresses. The issue of warpage is related to being a semi crystalline material, HDPE, being semi crystalline polymer, will have differential shrinkage along and across the flow leading to warpage. It is difficult to eliminate this problem just by optimizing processing ......
The Decription of China Mold Development[ 01-13 11:42 ]
1.Uneven development, overall level is not very high. Although many mold companies have reached the international advanced level, but on the whole china mold field, the precision of mold, cavity surface roughness, the production cycle, life and other index with foreign advanced level, there is a big ......
Shrinkage Difference Between PA66 GF50 & PA66 GF30[ 01-13 11:38 ]
This is an interesting question, because the lineal mold shrinkage is characteristic percent shrinkage of a plastic between melt processing and the final cooled article. Specifying materials of low shrinkage will make it easier to avoid problems of warpage and to increase dimensional precision of ......
Injection Molding Part With Crystalline Material[ 01-13 11:36 ]
We all know that the skin layer in a molded part with PP is less crystalline than the core in a PP injection molded component. Could you please explain the mechanism behind why it happens? Is it due to the rapid cooling during the cooling cycle during injection molding which prevents the formation of ......
Automotive Plastic Mould[ 01-13 11:32 ]
As we known, the auto business develop very quickly in past ten year, more and more newest go to the market, lots of automotive components are made from plastic, that means it need large amount of molds made. Ahead Technology(Shenzhen)Co.,ltd is specialized in various types of auto bumpers moulds and it’s ......
Understanding Injection Molding And Mold Flow Simulation[ 01-11 16:15 ]
In most cases injection mold shop will end up making "acceptable" parts by "shrink fixing" it. There goes all profit and residual stress is introduced. I am asking Chinese mold flow experts- have you produced mold flow simulations with tools where either part thickness varies and or cooling channels are not uniform, or are ......
The Document And Preparation Before Mold Shippment[ 01-11 16:11 ]
As plastic injection mold manufacturer, we should make sure the mold meet customer’s requirement. The checking procedure should be followed as below. We have to make sure all document needed are all packed in shipping box. 1, 2D mold assembly drawing with hard copy 2, 2D part drawing with hard copy 3, all the 2D drawing and 3D ......
MSI Mold Builders Expands In Lowa, Eyes Automotive Market[ 01-11 16:08 ]
ORLANDO, FLA. — MSI Mold Builders has recently completed a 12,000-square-foot expansion to its Cedar Rapids, Iowa, plant, bringing its total footprint to just under 60,000 square feet. The company also installed a 3-meter-by-6-meter travel 5-axis machining center and a 3,000-ton injection molding machine for ......
Injection Molding Materials[ 01-11 16:04 ]
A number of things come to my mind of using materials in injection mold, because some colors (especially phthalocyanins) could cause nucleation in both HDPE and PP, this could lead to stresses which are showing up in the colder environment. Just thinking out of the box.Have you thought of using any of the super tough grades of ......
Mold Making[ 01-08 09:57 ]
Mold design: The high quality mold is the core business of Ahead molding.we have 10 special mold designers, who have rich experience in resin Character and mold structure, and take each case seriously ,before designing start, our designer will run Mold Flow Analysis and attend a technical meet for each mold with ......
Low Volume Injection Molding Production Company[ 01-08 09:54 ]
When you design a new product, you want to trial them in the market before you invest lots of money to make big production, Now the problem come out, the big factory or famous company have the big amount for MOQ, but you worry about the quality with small shop, Now Ahead Mold focus on providing this ......
Injection Mold Venting Problem[ 01-08 09:50 ]
Venting can be one of the most important parts of an injection molded product. Many engineering materials like PBT (Polybutylene terephthalate) have a tendency of out-gassing. The best practices that I have to date are: Add 10mm wide vents spaced 30mm from each other all the way around parting line. Always follow the recommendations of the ......
Total number of records:306 | Pages:21  <...3456789101112...>  

Contact Ahead

Linkman: Tina Liu

Tel: +86-755-23426229

FAX: +86-755-29904981

Skype:tinaliu0128

E-mail:
tina@aheadmold.com

Add: No.36 Shiwei Pinggang Industrial Area, Jiangshi Community, Gongming Street, Guangming New District, Shenzhen, China 518106.

CONTACT

Ahead Technology(Shen Zhen) Co.,Ltd No.36 Shiwei Pinggang Industrial Area, Jiangshi Community,Gongming Street, Guangming New District, Shenzhen, China 518106

Phone: +86-755-23426229

Fax: +86-755-29904981

E-mail:tina@aheadmold.com

Stay in Touch

Sign up for our newsletter to receive event updates and exclusive offers

  • Email Address:
  • Leave your words here: